FW: cant get PCMCIA -> PCI card to work, attached is my kernel config

[Rob]

NM this issue, this was resolved by installing the rpms again.

Rob

>>-----Original Message-----
>>From: Rob [mailto:rwideman at austin.rr.com]
>>Sent: Wednesday, September 25, 2002 12:33 AM
>>To: wireless at lists.samba.org
>>Subject: cant get PCMCIA -> PCI card to work, attached is my kernel
>>config
>>
>>
>>After further investigation of my system it seems that 
>>/etc/pcmcia/* is not there.  If, after OS INSTALL i did: "rpm -e 
>><pcmcia-cs-3.2.1,kernel-pcmcia-cs-3.1.27-18>" AND THEN installed 
>>the pcmcia-cs-3.2.1.tar.gz and wireless_tools.25.tar.gz wouldnt 
>>"/etc/pcmcia/" now appear?
>>
>>Rob
>>
>>>>-----Original Message-----
>>>>From: Rob [mailto:rwideman at austin.rr.com]
>>>>Sent: Tuesday, September 24, 2002 11:59 PM
>>>>To: wireless at lists.samba.org
>>>>Subject: cant get PCMCIA -> PCI card to work, attached is my kernel
>>>>config
>>>>
>>>>
>>>>Any thoughts on this issue?......attached is my kernel config
>>>>
>>>>Components installed:
>>>>IBM HighRate Wireless LAN Card
>>>>ORiNOCO PCI Adapter
>>>>Linksys LNE100TX NIC (working using the tulip)
>>>>Kingston KNE111TX/100B NIC (working using the tulip)
>>>>
>>>>Here is output from dmesg:
>>>>***SKIPPING A FEW LINES***
>>>>All processors have done init_idle
>>>>PCI: PCI BIOS revision 2.10 entry at 0xfd88c, last bus=1
>>>>PCI: Using configuration type 1
>>>>PCI: Probing PCI hardware
>>>>Unknown bridge resource 0: assuming transparent
>>>>Unknown bridge resource 2: assuming transparent
>>>>PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
>>>>PCI: Found IRQ 9 for device 00:14.0
>>>>PCI: Sharing IRQ 9 with 01:00.0
>>>>***SKIPPING A FEW LINES***
>>>>Linux Tulip driver version 0.9.15-pre11 (May 11, 2002)
>>>>PCI: Found IRQ 15 for device 00:10.0
>>>>eth0: ADMtek Comet rev 17 at 0x7400, 00:04:5A:4C:CD:2D, IRQ 15.
>>>>PCI: Found IRQ 11 for device 00:12.0
>>>>eth1: Lite-On PNIC-II rev 37 at 0x7800, 00:C0:F0:75:C4:29, IRQ 11.
>>>>Linux Kernel Card Services 3.1.22
>>>>  options:  [pci] [cardbus]
>>>>PCI: Enabling device 00:14.0 (0000 -> 0002)
>>>>PCI: Found IRQ 9 for device 00:14.0
>>>>PCI: Sharing IRQ 9 with 01:00.0
>>>>***SKIPPING A FEW LINES***
>>>>[root at localhost root]# ifconfig
>>>>eth0      Link encap:Ethernet  HWaddr 00:04:5A:4C:CD:2D
>>>>          inet addr:192.168.1.40  Bcast:192.168.1.255  
>>Mask:255.255.255.0
>>>>          UP BROADCAST NOTRAILERS RUNNING MULTICAST  MTU:1500  Metric:1
>>>>          RX packets:430 errors:0 dropped:0 overruns:0 frame:0
>>>>          TX packets:279 errors:0 dropped:0 overruns:0 carrier:0
>>>>          collisions:0 txqueuelen:100
>>>>          RX bytes:30012 (29.3 Kb)  TX bytes:38723 (37.8 Kb)
>>>>          Interrupt:15 Base address:0x7400
>>>>
>>>>eth1      Link encap:Ethernet  HWaddr 00:C0:F0:75:C4:29
>>>>          inet addr:10.10.10.5  Bcast:10.255.255.255  Mask:255.0.0.0
>>>>          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>>>>          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>>>          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>>>          collisions:0 txqueuelen:100
>>>>          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
>>>>          Interrupt:11 Base address:0x7800
>>>>
>>>>lo        Link encap:Local Loopback
>>>>          inet addr:127.0.0.1  Mask:255.0.0.0
>>>>          UP LOOPBACK RUNNING  MTU:16436  Metric:1
>>>>          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>>>          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>>>          collisions:0 txqueuelen:0
>>>>          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
>>>>[root at localhost root]# iwconfig
>>>>lo        no wireless extensions.
>>>>
>>>>eth0      no wireless extensions.
>>>>
>>>>eth1      no wireless extensions.
>>>>
>>>>gre0      no wireless extensions.