[Samba] Update
sandy.napoles at eccmg.cupet.cu
sandy.napoles at eccmg.cupet.cu
Mon Mar 2 09:20:09 MST 2015
Yes I only writte git pull
> On 02/03/15 15:05, sandy.napoles at eccmg.cupet.cu wrote:
>> ifconfig -a
>> eth0 Link encap:Ethernet HWaddr 00:0c:29:82:ec:80
>> inet addr:172.18.68.8 Bcast:172.18.68.31
>> Mask:255.255.255.224
>> inet6 addr: fe80::20c:29ff:fe82:ec80/64 Scope:Link
>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>> RX packets:107940 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:109315 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:1000
>> RX bytes:14394078 (13.7 MiB) TX bytes:20253880 (19.3 MiB)
>>
>> lo Link encap:Local Loopback
>> inet addr:127.0.0.1 Mask:255.0.0.0
>> inet6 addr: ::1/128 Scope:Host
>> UP LOOPBACK RUNNING MTU:16436 Metric:1
>> RX packets:252 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:252 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:0
>> RX bytes:38555 (37.6 KiB) TX bytes:38555 (37.6 KiB)
>>
>>
>> ip -f inet6 route
>> fe80::/64 dev eth0 proto kernel metric 256
>>
>>
>>
>>> Thanks. No other interfaces (ifconfig -a)?
>>>
>>> Also output of
>>>
>>> ip -f inet6 route
>>>
>>> would be useful.
>>>
>>> David
>>> ------------------------------------------------------------------------
>>> Dr David Holder CEng FIET MIEEE
>>>
>>> Erion Ltd, An Cala, Inverkirkaig, Lochinver, Sutherland, IV27 4LR, UK
>>>
>>> Reception: +44 (0)1422 207000
>>>
>>> Direct Dial: +44 (0)131 2026317
>>>
>>> http://www.erion.co.uk
>>>
>>>
>>> Registered in England and Wales. Registered Number 3521142
>>> Registered Office: Newtons, 49 Coniscliffe Road, Darlington, County
>>> Durham, DL3 7EH, UK
>>> VAT Number: GB 698 3633 78
>>>
>>> On 02/03/2015 14:26, sandy.napoles at eccmg.cupet.cu wrote:
>>>> in /etc/gai.conf all is coment
>>>>
>>>>> Hi Sandy,
>>>>>
>>>>> Thanks! Curious. Do you have any other interfaces? ifconfig -a should
>>>>> show them all including loopback.
>>>>>
>>>>> What is puzzling me is that it should not even attempt to use IPv6 to
>>>>> reach a global address when it only has a link-local address. It
>>>>> should
>>>>> gracefully fall back to IPv4 (as per RFC 6724 or RFC 3484 depending
>>>>> on
>>>>> the kernel version). Since you have an IPv4 address and I assume an
>>>>> IPv4
>>>>> connection, then this should work over IPv4.
>>>>>
>>>>> I'm assume that you do not have an /etc/gai.conf file installed?
>>>>>
>>>>> David
>>>>> ------------------------------------------------------------------------
>>>>> Dr David Holder CEng FIET MIEEE
>>>>>
>>>>> Erion Ltd, An Cala, Inverkirkaig, Lochinver, Sutherland, IV27 4LR, UK
>>>>>
>>>>> Reception: +44 (0)1422 207000
>>>>>
>>>>> Direct Dial: +44 (0)131 2026317
>>>>>
>>>>> http://www.erion.co.uk
>>>>>
>>>>>
>>>>> Registered in England and Wales. Registered Number 3521142
>>>>> Registered Office: Newtons, 49 Coniscliffe Road, Darlington, County
>>>>> Durham, DL3 7EH, UK
>>>>> VAT Number: GB 698 3633 78
>>>>>
>>>>> On 02/03/2015 13:10, sandy.napoles at eccmg.cupet.cu wrote:
>>>>>> eth0 Link encap:Ethernet HWaddr d0:27:88:64:e4:01
>>>>>> inet addr:172.18.70.100 Mask:255.255.255.224
>>>>>> inet6 addr: fe80::d227:88ff:fe64:e401/64 Scope:Link
>>>>>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>>>>>> RX packets:1413908 errors:0 dropped:0 overruns:0
>>>>>> frame:0
>>>>>> TX packets:447039 errors:0 dropped:0 overruns:0
>>>>>> carrier:0
>>>>>> collisions:0 txqueuelen:1000
>>>>>> RX bytes:1693689457 (1.5 GiB) TX bytes:52974612 (50.5
>>>>>> MiB)
>>>>>> Interrupt:43 Base address:0xc000
>>>>>>
>>>>>>
>>>>>> traceroute6 git.samba.org
>>>>>> traceroute to git.samba.org (2001:638:603:d06e::80:230), 30 hops
>>>>>> max,
>>>>>> 80
>>>>>> byte packets
>>>>>> connect: Network is unreachable
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>> Hi Sandy,
>>>>>>>
>>>>>>> Please can you provide the output from an *i**fconfig -a* command?
>>>>>>>
>>>>>>> This should give an idea of what is going on. Turning off IPv6 will
>>>>>>> not
>>>>>>> be necessary if you can find the actual cause of the problem.
>>>>>>>
>>>>>>> You would not get this error message if you only have a link local
>>>>>>> address configured on your interface. You must have some form of
>>>>>>> global
>>>>>>> address.
>>>>>>>
>>>>>>> Also, the IPv6 address is that of git.samba.org not samba.org. You
>>>>>>> could
>>>>>>> try:
>>>>>>>
>>>>>>> *traceroute6 git.samba.org.*
>>>>>>>
>>>>>>> Best Regards,
>>>>>>> David
>>>>>>> ------------------------------------------------------------------------
>>>>>>> Dr David Holder CEng FIET MIEEE
>>>>>>>
>>>>>>> Erion Ltd, An Cala, Inverkirkaig, Lochinver, Sutherland, IV27 4LR,
>>>>>>> UK
>>>>>>>
>>>>>>> Reception: +44 (0)1422 207000
>>>>>>>
>>>>>>> Direct Dial: +44 (0)131 2026317
>>>>>>>
>>>>>>> http://www.erion.co.uk
>>>>>>>
>>>>>>>
>>>>>>> Registered in England and Wales. Registered Number 3521142
>>>>>>> Registered Office: Newtons, 49 Coniscliffe Road, Darlington, County
>>>>>>> Durham, DL3 7EH, UK
>>>>>>> VAT Number: GB 698 3633 78
>>>>>>>
>>>>>>> On 28/02/2015 18:38, Reindl Harald wrote:
>>>>>>>> Am 28.02.2015 um 19:13 schrieb sandy.napoles at eccmg.cupet.cu:
>>>>>>>>> I do not working with ipv6, I have disable, but I have the same
>>>>>>>>> error,
>>>>>>>>> I
>>>>>>>>> can read in internet that this ipv6 ip 2001:638:603:d06e::80:230:
>>>>>>>>> belong
>>>>>>>>> to url samba.org....
>>>>>>>>>
>>>>>>>>> If I try to connect to this url using some navegator I connected
>>>>>>>>> perfect....but when I run git pull using command line I can not
>>>>>>>>> connect..
>>>>>>>> the question is *how* did you disable ipv6 - when ifconfig shows a
>>>>>>>> "link local" ipv6 address the stack is *not* entirely disabled
>>>>>>>>
>>>>>>>> [root at srv-rhsoft:~]$ ifconfig eth0
>>>>>>>> eth0: flags=4419<UP,BROADCAST,RUNNING,PROMISC,MULTICAST> mtu 1500
>>>>>>>> ether 24:be:05:1a:c0:27 txqueuelen 100 (Ethernet)
>>>>>>>> RX packets 2460 bytes 577531 (563.9 KiB)
>>>>>>>> RX errors 0 dropped 0 overruns 0 frame 0
>>>>>>>> TX packets 8722 bytes 1981928 (1.8 MiB)
>>>>>>>> TX errors 0 dropped 0 overruns 0 carrier 0
>>>>>>>> collisions 0
>>>>>>>> device interrupt 20 memory 0xf7e00000-f7e20000
>>>>>>>>
>>>>>>>>>> Am 28.02.2015 um 15:37 schrieb sandy.napoles at eccmg.cupet.cu:
>>>>>>>>>>> Hello list, Iam using samba4 as Domain Controller my verion
>>>>>>>>>>> Version
>>>>>>>>>>> 4.3.0pre1-GIT-068f9e2, but I have a little problem when I going
>>>>>>>>>>> to
>>>>>>>>>>> update
>>>>>>>>>>> using GIT PULL I have this error
>>>>>>>>>>>
>>>>>>>>>>> error: Failed to connect to 2001:638:603:d06e::80:230: Network
>>>>>>>>>>> is
>>>>>>>>>>> unreachable while accessing
>>>>>>>>>>> http://git.samba.org/samba.git/info/refs
>>>>>>>>>>> fatal: HTTP request failed
>>>>>>>>>>>
>>>>>>>>>>> some body can helpme
>>>>>>>>>> do you have working ipv6?
>>>>>>>>>> if not disable it via sysctl.conf
>>>>>>>>>>
>>>>>>>>>> net.ipv6.conf.all.disable_ipv6=1
>>>>>>>>>> net.ipv6.conf.default.disable_ipv6=1
>>>>>>>>>>
>>>>>>>>>> that above is most likely because the link-local address if the
>>>>>>>>>> ipv6
>>>>>>>>>> stack is enabled and some piece of software thinks it's useable
>>>>>>>>>>
>>>>>>>>>> --
>>>>>>>>>> To unsubscribe from this list go to the following URL and read
>>>>>>>>>> the
>>>>>>>>>> instructions: https://lists.samba.org/mailman/options/samba
>>>>>>> --
>>>>>>> To unsubscribe from this list go to the following URL and read the
>>>>>>> instructions: https://lists.samba.org/mailman/options/samba
>>>>>>>
>>>>> --
>>>>> To unsubscribe from this list go to the following URL and read the
>>>>> instructions: https://lists.samba.org/mailman/options/samba
>>>>>
>>> --
>>> To unsubscribe from this list go to the following URL and read the
>>> instructions: https://lists.samba.org/mailman/options/samba
>>>
>>
>
> OK, nobody seems to have asked this yet, what OS and how are you trying
> to update git, just what are you typing into the terminal ?
>
> Rowland
>
> --
> To unsubscribe from this list go to the following URL and read the
> instructions: https://lists.samba.org/mailman/options/samba
>
More information about the samba
mailing list