[clug] raid tries to init before sata modules loaded

[Michael Manning]

Rob,

What distro & kernel are you using - normally I would not expect a 
filesystem module to load until after device detection either.
Do you have any other HDD's in the box that have been detected prior to 
the snip given?



Rob Shugg wrote:
> Guys
> it looks like my reiser modules are trying to load before the raid is 
> initialised is there a simple way to fix this or do I have to build 
> reiser into the kernel? see relevant dmsg below
> 
> rob
> 
> 
> ReiserFS: md0: warning: sh-2006: read_super_block: bread failed (dev 
> md0, block
> 2, size 4096)
> ReiserFS: md0: warning: sh-2006: read_super_block: bread failed (dev 
> md0, block
> 16, size 4096)
> ReiserFS: md0: warning: sh-2021: reiserfs_fill_super: can not find 
> reiserfs on m
> d0
> e1000: Ignoring new-style parameters in presence of obsolete ones
> Intel(R) PRO/1000 Network Driver - version 5.2.52-k4
> Copyright (c) 1999-2004 Intel Corporation.
> e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
> SCSI subsystem initialized
> libata version 1.02 loaded.
> sata_sil version 0.54
> ata1: SATA max UDMA/100 cmd 0xF8811C80 ctl 0xF8811C8A bmdma 0xF8811C00 
> irq 19
> ata2: SATA max UDMA/100 cmd 0xF8811CC0 ctl 0xF8811CCA bmdma 0xF8811C08 
> irq 19
> ata3: SATA max UDMA/100 cmd 0xF8811E80 ctl 0xF8811E8A bmdma 0xF8811E00 
> irq 19
> ata4: SATA max UDMA/100 cmd 0xF8811EC0 ctl 0xF8811ECA bmdma 0xF8811E08 
> irq 19
> ata1: no device found (phy stat 00000000)
> scsi0 : sata_sil
> ata2: no device found (phy stat 00000000)
> scsi1 : sata_sil
> ata3: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003 
> 88:203f
> ata3: dev 0 ATA, max UDMA/100, 390721968 sectors: lba48
> ata3: dev 0 configured for UDMA/100
> scsi2 : sata_sil
> ata4: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003 
> 88:203f
> ata4: dev 0 ATA, max UDMA/100, 390721968 sectors: lba48
> ata4: dev 0 configured for UDMA/100
> scsi3 : sata_sil
>   Vendor: ATA       Model: WDC WD2000JD-00G  Rev: 02.0
>   Type:   Direct-Access                      ANSI SCSI revision: 05
>   Vendor: ATA       Model: WDC WD2000JD-00G  Rev: 02.0
>   Type:   Direct-Access                      ANSI SCSI revision: 05
> SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
> SCSI device sda: drive cache: write back
>  /dev/scsi/host2/bus0/target0/lun0: unknown partition table
> Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
> SCSI device sdb: 390721968 512-byte hdwr sectors (200050 MB)
> SCSI device sdb: drive cache: write back
>  /dev/scsi/host3/bus0/target0/lun0: unknown partition table
> Attached scsi disk sdb at scsi3, channel 0, id 0, lun 0

-- 
Michael Manning
Red Hat Certified Engineer

Email: michael at michaelmanning.org
Website: http://michaelmanning.org/