[clug] raid tries to init before sata modules loaded

[Steve Walsh]

Rob;

What flavour and Kernel are you running? What type of Raid are you trying to
run (0,1,5, etc?)

Does /var/log/message give any indicator? Some old posts to
linux.debian.user group indicated there was a bug found in drivers/md/md.c
on sarge around line 1510, but I can't remember the Kernel Version this
occurred in. From memory upgrading the Kernel fixed it, but if you are
running a new Kernel release I suppose that won't help.


Steve
-----Original Message-----
From: linux-bounces+steve=nerdvana.org.au at lists.samba.org
[mailto:linux-bounces+steve=nerdvana.org.au at lists.samba.org]On Behalf Of
Rob Shugg
Sent: Thursday, 2 September 2004 12:41 PM
To: linux at samba.org
Subject: [clug] raid tries to init before sata modules loaded


Guys
it looks like my reiser modules are trying to load before the raid is
initialised is there a simple way to fix this or do I have to build reiser
into
the kernel? see relevant dmsg below

rob


ReiserFS: md0: warning: sh-2006: read_super_block: bread failed (dev md0,
block
2, size 4096)
ReiserFS: md0: warning: sh-2006: read_super_block: bread failed (dev md0,
block
16, size 4096)
ReiserFS: md0: warning: sh-2021: reiserfs_fill_super: can not find reiserfs
on m
d0
e1000: Ignoring new-style parameters in presence of obsolete ones
Intel(R) PRO/1000 Network Driver - version 5.2.52-k4
Copyright (c) 1999-2004 Intel Corporation.
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
SCSI subsystem initialized
libata version 1.02 loaded.
sata_sil version 0.54
ata1: SATA max UDMA/100 cmd 0xF8811C80 ctl 0xF8811C8A bmdma 0xF8811C00 irq
19
ata2: SATA max UDMA/100 cmd 0xF8811CC0 ctl 0xF8811CCA bmdma 0xF8811C08 irq
19
ata3: SATA max UDMA/100 cmd 0xF8811E80 ctl 0xF8811E8A bmdma 0xF8811E00 irq
19
ata4: SATA max UDMA/100 cmd 0xF8811EC0 ctl 0xF8811ECA bmdma 0xF8811E08 irq
19
ata1: no device found (phy stat 00000000)
scsi0 : sata_sil
ata2: no device found (phy stat 00000000)
scsi1 : sata_sil
ata3: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003
88:203f
ata3: dev 0 ATA, max UDMA/100, 390721968 sectors: lba48
ata3: dev 0 configured for UDMA/100
scsi2 : sata_sil
ata4: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003
88:203f
ata4: dev 0 ATA, max UDMA/100, 390721968 sectors: lba48
ata4: dev 0 configured for UDMA/100
scsi3 : sata_sil
   Vendor: ATA       Model: WDC WD2000JD-00G  Rev: 02.0
   Type:   Direct-Access                      ANSI SCSI revision: 05
   Vendor: ATA       Model: WDC WD2000JD-00G  Rev: 02.0
   Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
SCSI device sda: drive cache: write back
  /dev/scsi/host2/bus0/target0/lun0: unknown partition table
Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
SCSI device sdb: 390721968 512-byte hdwr sectors (200050 MB)
SCSI device sdb: drive cache: write back
  /dev/scsi/host3/bus0/target0/lun0: unknown partition table
Attached scsi disk sdb at scsi3, channel 0, id 0, lun 0
--
CTO
KPT  Canberra
http://kinetitech.com.au
Ph 61 2 61621770

--
linux mailing list
linux at lists.samba.org
http://lists.samba.org/mailman/listinfo/linux