Error -5 writing Tx descriptor to BAP

[wlan]

I have been working with a orinoco silver for 2 month without problems.
The only change that i have made it is to upgrade to kernel-2.4.18-5 from
redhat updates. I have reading older post and orinoco Readme and this error
should be corrected since orinoco_cs 0.09a.
Now sometimes i get the following error:
eth2: Error -5 writing Tx descriptor to BAP
(many times...........................)

It has nothing to do with network load, as it happens at pcmcia start up and
without any network load!

Any clue?, what should i test? Do you need more information?




================================================================
SUM UP:
RH 7.3
kernel-2.4.18-5
wireless-tools-24-2
kernel-pcmcia-cs-3.1.31-3
PCI-PCMIA adapter: Texas Instruments PCI1410 PC
Lucent Technologies Silver firmware version 7.28
orinoco_cs.c 0.11b

== VERBOSE OUTPUT==

#cardctl ident
Socket 0:
  product info: "Lucent Technologies", "WaveLAN/IEEE", "Version 01.01", ""
  manfid: 0x0156, 0x0002
  function: 6 (network)

#/etc/syconfig/pcmcia start
Linux Kernel Card Services 3.1.22
  options:  [pci] [cardbus] [pm]
PCI: Found IRQ 12 for device 00:0a.0
Yenta IRQ list 0000, PCI irq12
Socket status: 10000011
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x207 0x378-0x37f
0x4d0-0x4d7cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
hermes.c: 5 Apr 2002 David Gibson <hermes at gibson.dropbear.id.au>
orinoco.c 0.11b (David Gibson <hermes at gibson.dropbear.id.au> and others)
orinoco_cs.c 0.11b (David Gibson <hermes at gibson.dropbear.id.au> and others)
eth2: Station identity 001f:0001:0007:001c
eth2: Looks like a Lucent/Agere firmware version 7.28
eth2: Ad-hoc demo mode supported
eth2: IEEE standard IBSS ad-hoc mode supported
eth2: WEP supported, 104-bit key
eth2: MAC address 00:02:2D:3B:23:33
eth2: Station name "HERMES I"
eth2: ready
eth2: index 0x01: Vcc 5.0, irq 12, io 0x0100-0x013f

#lspci -vvv
00:0a.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller
(rev 01)
        Subsystem: SCM Microsystems: Unknown device 3000
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 168, cache line size 04
        Interrupt: pin A routed to IRQ 12
        Region 0: Memory at db003000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
        Memory window 0: db000000-db001000 (prefetchable)
        Memory window 1: 10000000-103ff000
        I/O window 0: 00004000-000040ff
        I/O window 1: 00004400-000044ff
        BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite+
        16-bit legacy interface ports at 0001

#cat /etc/sysconfig/pcmcia
PCIC=i82365