[Samba] Installing onto Windows
L.P.H. van Belle
belle at bazuin.nl
Tue Mar 15 12:50:07 UTC 2016
Since this is a standalone server.
Change
map to guest = bad user
to
map to guest = bad password
put the 2 pc's hostnames in the /etc/hosts file on the samba server.
Stop and start samba.
And it helps if
In smb.conf : workgroup = WORKGROUP and workgroup in windows are the same.
Can you access based on \\ip\share and \\hostname\share ?
Greetz,
Louis
> -----Oorspronkelijk bericht-----
> Van: samba [mailto:samba-bounces at lists.samba.org] Namens Rowland penny
> Verzonden: dinsdag 15 maart 2016 13:26
> Aan: sambalist
> Onderwerp: Re: [Samba] Installing onto Windows
>
> On 15/03/16 12:12, Douglas Holden wrote:
> > #
> > # Sample configuration file for the Samba suite for Debian GNU/Linux.
> > #
> > #
> > # This is the main Samba configuration file. You should read the
> > # smb.conf(5) manual page in order to understand the options listed
> > # here. Samba has a huge number of configurable options most of which
> > # are not shown in this example
> > #
> > # Some options that are often worth tuning have been included as
> > # commented-out examples in this file.
> > # - When such options are commented with ";", the proposed setting
> > # differs from the default Samba behaviour
> > # - When commented with "#", the proposed setting is the default
> > # behaviour of Samba but the option is considered important
> > # enough to be mentioned here
> > #
> > # NOTE: Whenever you modify this file you should run the command
> > # "testparm" to check that you have not made any basic syntactic
> > # errors.
> >
> > #======================= Global Settings =======================
> >
> > [global]
> >
> > ## Browsing/Identification ###
> >
> > # Change this to the workgroup/NT-domain name your Samba server will
> > part of
> > workgroup = WORKGROUP
> >
> > # server string is the equivalent of the NT Description field
> > server string = %h server (Samba, Linux Mint)
> >
> > # Windows Internet Name Serving Support Section:
> > # WINS Support - Tells the NMBD component of Samba to enable its WINS
> > Server
> > # wins support = no
> >
> > # WINS Server - Tells the NMBD components of Samba to be a WINS Client
> > # Note: Samba can be either a WINS Server, or a WINS Client, but NOT
> both
> > ; wins server = w.x.y.z
> >
> > # This will prevent nmbd to search for NetBIOS names through DNS.
> > dns proxy = no
> >
> > #### Networking ####
> >
> > # The specific set of interfaces / networks to bind to
> > # This can be either the interface name or an IP address/netmask;
> > # interface names are normally preferred
> > ; interfaces = 127.0.0.0/8 eth0
> >
> > # Only bind to the named interfaces and/or networks; you must use the
> > # 'interfaces' option above to use this.
> > # It is recommended that you enable this feature if your Samba machine
> is
> > # not protected by a firewall or is a firewall itself. However, this
> > # option cannot handle dynamic or non-broadcast interfaces correctly.
> > ; bind interfaces only = yes
> >
> >
> >
> > #### Debugging/Accounting ####
> >
> > # This tells Samba to use a separate log file for each machine
> > # that connects
> > log file = /var/log/samba/log.%m
> >
> > # Cap the size of the individual log files (in KiB).
> > max log size = 1000
> >
> > # If you want Samba to only log through syslog then set the following
> > # parameter to 'yes'.
> > # syslog only = no
> >
> > # We want Samba to log a minimum amount of information to syslog.
> > Everything
> > # should go to /var/log/samba/log.{smbd,nmbd} instead. If you want to
> log
> > # through syslog you should set the following parameter to something
> > higher.
> > syslog = 0
> >
> > # Do something sensible when Samba crashes: mail the admin a backtrace
> > panic action = /usr/share/samba/panic-action %d
> >
> >
> > ####### Authentication #######
> >
> > # Server role. Defines in which mode Samba will operate. Possible
> > # values are "standalone server", "member server", "classic primary
> > # domain controller", "classic backup domain controller", "active
> > # directory domain controller".
> > #
> > # Most people will want "standalone sever" or "member server".
> > # Running as "active directory domain controller" will require first
> > # running "samba-tool domain provision" to wipe databases and create a
> > # new domain.
> > server role = standalone server
> >
> > # If you are using encrypted passwords, Samba will need to know what
> > # password database type you are using.
> > passdb backend = tdbsam
> >
> > obey pam restrictions = yes
> >
> > # This boolean parameter controls whether Samba attempts to sync the
> Unix
> > # password with the SMB password when the encrypted SMB password in the
> > # passdb is changed.
> > unix password sync = yes
> >
> > # For Unix password sync to work on a Debian GNU/Linux system, the
> > following
> > # parameters must be set (thanks to Ian Kahan
> > <<kahan at informatik.tu-muenchen.de> for
> > # sending the correct chat script for the passwd program in Debian
> Sarge).
> > passwd program = /usr/bin/passwd %u
> > passwd chat = *Enter\snew\s*\spassword:* %n\n
> > *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* .
> >
> > # This boolean controls whether PAM will be used for password changes
> > # when requested by an SMB client instead of the program listed in
> > # 'passwd program'. The default is 'no'.
> > pam password change = yes
> >
> > # This option controls how unsuccessful authentication attempts are
> mapped
> > # to anonymous connections
> > map to guest = bad user
> >
> > ########## Domains ###########
> >
> > #
> > # The following settings only takes effect if 'server role = primary
> > # classic domain controller', 'server role = backup domain controller'
> > # or 'domain logons' is set
> > #
> >
> > # It specifies the location of the user's
> > # profile directory from the client point of view) The following
> > # required a [profiles] share to be setup on the samba server (see
> > # below)
> > ; logon path = \\%N\profiles\%U
> > # Another common choice is storing the profile in the user's home
> > directory
> > # (this is Samba's default)
> > # logon path = \\%N\%U\profile
> >
> > # The following setting only takes effect if 'domain logons' is set
> > # It specifies the location of a user's home directory (from the client
> > # point of view)
> > ; logon drive = H:
> > # logon home = \\%N\%U
> >
> > # The following setting only takes effect if 'domain logons' is set
> > # It specifies the script to run during logon. The script must be stored
> > # in the [netlogon] share
> > # NOTE: Must be store in 'DOS' file format convention
> > ; logon script = logon.cmd
> >
> > # This allows Unix users to be created on the domain controller via
> > the SAMR
> > # RPC pipe. The example command creates a user account with a
> > disabled Unix
> > # password; please adapt to your needs
> > ; add user script = /usr/sbin/adduser --quiet --disabled-password
> > --gecos "" %u
> >
> > # This allows machine accounts to be created on the domain controller
> > via the
> > # SAMR RPC pipe.
> > # The following assumes a "machines" group exists on the system
> > ; add machine script = /usr/sbin/useradd -g machines -c "%u machine
> > account" -d /var/lib/samba -s /bin/false %u
> >
> > # This allows Unix groups to be created on the domain controller via
> > the SAMR
> > # RPC pipe.
> > ; add group script = /usr/sbin/addgroup --force-badname %g
> >
> > ############ Misc ############
> >
> > # Using the following line enables you to customise your configuration
> > # on a per machine basis. The %m gets replaced with the netbios name
> > # of the machine that is connecting
> > ; include = /home/samba/etc/smb.conf.%m
> >
> > # Some defaults for winbind (make sure you're not using the ranges
> > # for something else.)
> > ; idmap uid = 10000-20000
> > ; idmap gid = 10000-20000
> > ; template shell = /bin/bash
> >
> > # Setup usershare options to enable non-root users to share folders
> > # with the net usershare command.
> >
> > # Maximum number of usershare. 0 (default) means that usershare is
> > disabled.
> > ; usershare max shares = 100
> >
> > # Allow users who've been granted usershare privileges to create
> > # public shares, not just authenticated ones
> > usershare allow guests = yes
> >
> > #======================= Share Definitions =======================
> >
> > # Un-comment the following (and tweak the other settings below to suit)
> > # to enable the default home directory shares. This will share each
> > # user's home directory as \\server\username
> > ;[homes]
> > ; comment = Home Directories
> > ; browseable = no
> >
> > # By default, the home directories are exported read-only. Change the
> > # next parameter to 'no' if you want to be able to write to them.
> > ; read only = yes
> >
> > # File creation mask is set to 0700 for security reasons. If you want to
> > # create files with group=rw permissions, set next parameter to 0775.
> > ; create mask = 0700
> >
> > # Directory creation mask is set to 0700 for security reasons. If you
> > want to
> > # create dirs. with group=rw permissions, set next parameter to 0775.
> > ; directory mask = 0700
> >
> > # By default, \\server\username shares can be connected to by anyone
> > # with access to the samba server.
> > # Un-comment the following parameter to make sure that only "username"
> > # can connect to \\server\username
> > # This might need tweaking when using external authentication schemes
> > ; valid users = %S
> >
> > # Un-comment the following and create the netlogon directory for
> > Domain Logons
> > # (you need to configure Samba to act as a domain controller too.)
> > ;[netlogon]
> > ; comment = Network Logon Service
> > ; path = /home/samba/netlogon
> > ; guest ok = yes
> > ; read only = yes
> >
> > # Un-comment the following and create the profiles directory to store
> > # users profiles (see the "logon path" option above)
> > # (you need to configure Samba to act as a domain controller too.)
> > # The path below should be writable by all users so that their
> > # profile directory may be created the first time they log on
> > ;[profiles]
> > ; comment = Users profiles
> > ; path = /home/samba/profiles
> > ; guest ok = no
> > ; browseable = no
> > ; create mask = 0600
> > ; directory mask = 0700
> >
> > [printers]
> > comment = All Printers
> > browseable = no
> > path = /var/spool/samba
> > printable = yes
> > guest ok = no
> > read only = yes
> > create mask = 0700
> >
> > # Windows clients look for this share name as a source of downloadable
> > # printer drivers
> > [print$]
> > comment = Printer Drivers
> > path = /var/lib/samba/printers
> > browseable = yes
> > read only = yes
> > guest ok = no
> > # Uncomment to allow remote administration of Windows print drivers.
> > # You may need to replace 'lpadmin' with the name of the group your
> > # admin users are members of.
> > # Please note that you also need to set appropriate Unix permissions
> > # to the drivers directory for these users to have write rights in it
> > ; write list = root, @lpadmin
> >
> >
> >
>
> OK, that looks very much like the default smb.conf, have you actually
> set up Samba ?
> Are the 'smbd', 'nmbd' and 'winbind' deamons running, or to put it
> another way, have you started them ?
>
> Rowland
>
> --
> To unsubscribe from this list go to the following URL and read the
> instructions: https://lists.samba.org/mailman/options/samba
More information about the samba
mailing list