[Samba] getting NT_STATUS_LOGON_FAILURE

Bob of Donelson Trophy bob at donelsontrophy.net
Fri Jan 9 11:31:40 MST 2015


 

On 2015-01-09 11:40, Rowland Penny wrote: 

> On 09/01/15 17:26, Bob of Donelson Trophy wrote:
> On 2015-01-09 10:23, Rowland Penny wrote: On 09/01/15 15:47, Bob of Donelson Trophy wrote: On 2015-01-09 09:27, Rowland Penny wrote: On 09/01/15 15:00, Bob of Donelson Trophy wrote: On 2015-01-09 08:44, Rowland Penny wrote: W7 client "Preferred DNS server" is set to my DC. My DC looks like this: root at dtdc01:~# cat /etc/resolv.conf search dtshrm.local domain dtshrm.local nameserver 192.168.16.54 root at dtdc01:~# cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet static address 192.168.16.54 netmask 255.255.255.0 network 192.168.16.0 broadcast 192.168.16.255 gateway 192.168.16.106 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 208.67.222.222 dns-search dtshrm.local root at dtdc01:~# cat /etc/hosts
127.0.0.1 localhost 192.168.16.54 dtdc01.dtshrm.lan dtdc01 # The following lines are desirable for IPv6 capable hosts ::1 localhost ip6-localhost ip6-loopback ff02::1 ip6-allnodes f

f

> 02::2 ip6-allrouters Should the /etc/resolv.conf be resolving to itself? (I chuckled at you "panic" comment. lol) Fix this first, checking for 'libnss_winbind.so.2' is next on my list for this morning. 
> 
>> Firstly, what email client are you using ? it appears to be doing weird things :-) Don't bother about libnss_winbind.so.2, you have it, what you don't have is the pam config file that automatically sets pam. This is my /etc/resolv.conf from my DC: nameserver 127.0.0.1 search example.lan It needs to point to itself and you do not need the domain line. domain & search are mutually exclusive and the last one wins. This is my /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.2 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.1 I also turn off NetworkManager and stop it from starting at boot. When you installed your member server via Louis's script, did you alter this line: ENABLEPAMAUTH=0 Rowland
> Email client - Louis' email came back looking weird. Don't know about that. How do I "turn off NetworkManager" in Debian? (I didn't think it was on a server non-gui install?) Ah, didn't know that, you do not have it running. 
> 
>> And I have not altered any PAM lines so I have not changes ENABLEPAMAUTH=0 however, where is it so I can go check it?
> It is in Louis's script, line 100 and if you change it to 1 it runs a block of code starting at line 349, this modifies /etc/pam.d/samba. This is not what happens if you install libnss-winbind & libpam-winbind with the debian samba4 packages, unfortunately you cannot install these with the sernet packages, but most of the contents of those two packages are in sernet-samba-libs, except for the pam config file: /usr/share/pam-configs/winbind Name: Winbind NT/Active Directory authentication Default: yes Priority: 192 Auth-Type: Primary Auth: [success=end default=ignore] pam_winbind.so krb5_auth krb5_ccache_type=FILE cached_login try_first_pass Auth-Initial: [success=end default=ignore] pam_winbind.so krb5_auth krb5_ccache_type=FILE cached_login Account-Type: Primary Account: [success=end new_authtok_reqd=done default=ignore] pam_winbind.so Password-Type: Primary Password: [success=end default=ignore] pam_winbind.so use_authtok try_first_pass Password-Initial: [success=end
default=ignore] pam_winbind.so Session-Type: Additional Session: optional pam_winbind.so You may have to run 'pam-auth-update' and select winbind. Rowland 
> 
>> -- ------------------------- Bob Wooden of Donelson Trophy 615.885.2846 (main) www.donelsontrophy.com [1] [1] "Everyone deserves an award!!"
> Okay, I have resolved my (stupid Windows) "No internet access" issue on my lone W7 client. Moving forward with resolving my "getting NT_STATUS_LOGON_FAILURE" issue. I went to my (modified for me) script and I had "ENABLEPAMAUTH=0" and "ENABLEPAMSSH=0". Maybe I should simply restore my member server with 'pre-script backup' and re-run the script with these two options enabled (set to 1)? Should I enable both or just the "ENABLEAUTH"? Or can we (with your help, I hope) correct this issue?

As you have a backup, try creating the pam-config script I posted and
then run 'pam-auth-update --package', this should get you the same pam
setup as my member server.

Rowland

Maybe I about to do this incorrectly. I create to config file (you sent
me) with 'vi /usr/share/pam-configs/winbind' and then started to run
"pam-auth-update". Now do I update all three all services listed
(Kerberos, Unix and Winbind) or just winbind only? 
-- 

-------------------------

Bob Wooden of Donelson Trophy

615.885.2846 (main)
www.donelsontrophy.com [1]

"Everyone deserves an award!!"
 

Links:
------
[1] http://www.donelsontrophy.com


More information about the samba mailing list