[Samba] getting NT_STATUS_LOGON_FAILURE

[Rowland Penny]

On 09/01/15 17:26, Bob of Donelson Trophy wrote:
>   
>
> On 2015-01-09 10:23, Rowland Penny wrote:
>
>> On 09/01/15 15:47, Bob of Donelson Trophy wrote:
>>
>> On 2015-01-09 09:27, Rowland Penny wrote:
>>
>> On 09/01/15 15:00, Bob of Donelson Trophy wrote:
>> On 2015-01-09 08:44, Rowland Penny wrote: W7 client "Preferred DNS server" is set to my DC. My DC looks like this: root at dtdc01:~# cat /etc/resolv.conf search dtshrm.local domain dtshrm.local nameserver 192.168.16.54 root at dtdc01:~# cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet static address 192.168.16.54 netmask 255.255.255.0 network 192.168.16.0 broadcast 192.168.16.255 gateway 192.168.16.106 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 208.67.222.222 dns-search dtshrm.local root at dtdc01:~# cat /etc/hosts 127.0.0.1 localhost 192.168.16.54 dtdc01.dtshrm.lan dtdc01 # The following lines are desirable for IPv6 capable hosts ::1 localhost ip6-localhost ip6-loopback ff02::1 ip6-allnodes ff
>   02::2
> ip6-allrouters Should the /etc/resolv.conf be resolving to itself? (I chuckled at you "panic" comment. lol) Fix this first, checking for 'libnss_winbind.so.2' is next on my list for this morning.
>> Firstly, what email client are you using ? it appears to be doing weird things :-)
>>
>> Don't bother about libnss_winbind.so.2, you have it, what you don't have is the pam config file that automatically sets pam.
>>
>> This is my /etc/resolv.conf from my DC:
>>
>> nameserver 127.0.0.1
>> search example.lan
>>
>> It needs to point to itself and you do not need the domain line. domain & search are mutually exclusive and the last one wins.
>>
>> This is my /etc/network/interfaces
>>
>> # This file describes the network interfaces available on your system
>> # and how to activate them. For more information, see interfaces(5).
>>
>> # The loopback network interface
>> auto lo
>> iface lo inet loopback
>>
>> auto eth0
>> iface eth0 inet static
>> address 192.168.0.2
>> netmask 255.255.255.0
>> network 192.168.0.0
>> broadcast 192.168.0.255
>> gateway 192.168.0.1
>>
>> I also turn off NetworkManager and stop it from starting at boot.
>>
>> When you installed your member server via Louis's script, did you alter this line:
>>
>> ENABLEPAMAUTH=0
>>
>> Rowland
> Email client - Louis' email came back looking weird. Don't know about
> that.
>
> How do I "turn off NetworkManager" in Debian? (I didn't think it was on
> a server non-gui install?)
>   Ah, didn't know that, you do not have it running.
>
>> And I have not altered any PAM lines so I have not changes ENABLEPAMAUTH=0 however, where is it so I can go check it?
>   It is in Louis's script, line 100 and if you change it to 1 it runs a
> block of code starting at line 349, this modifies /etc/pam.d/samba.
>   This is not what happens if you install libnss-winbind & libpam-winbind
> with the debian samba4 packages, unfortunately you cannot install these
> with the sernet packages, but most of the contents of those two packages
> are in sernet-samba-libs, except for the pam config file:
>
>   /usr/share/pam-configs/winbind
>
>   Name: Winbind NT/Active Directory authentication
>   Default: yes
>   Priority: 192
>   Auth-Type: Primary
>   Auth:
>   [success=end default=ignore] pam_winbind.so krb5_auth
> krb5_ccache_type=FILE cached_login try_first_pass
>   Auth-Initial:
>   [success=end default=ignore] pam_winbind.so krb5_auth
> krb5_ccache_type=FILE cached_login
>   Account-Type: Primary
>   Account:
>   [success=end new_authtok_reqd=done default=ignore] pam_winbind.so
>   Password-Type: Primary
>   Password:
>   [success=end default=ignore] pam_winbind.so use_authtok try_first_pass
>   Password-Initial:
>   [success=end default=ignore] pam_winbind.so
>   Session-Type: Additional
>   Session:
>   optional pam_winbind.so
>
>   You may have to run 'pam-auth-update' and select winbind.
>
>   Rowland
>
>> -- 
>>
>> -------------------------
>>
>> Bob Wooden of Donelson Trophy
>>
>> 615.885.2846 (main)
>> www.donelsontrophy.com [1]
>>
>> "Everyone deserves an award!!"
> Okay, I have resolved my (stupid Windows) "No internet access" issue on
> my lone W7 client.
>
> Moving forward with resolving my "getting NT_STATUS_LOGON_FAILURE"
> issue.
>
> I went to my (modified for me) script and I had "ENABLEPAMAUTH=0" and
> "ENABLEPAMSSH=0". Maybe I should simply restore my member server with
> 'pre-script backup' and re-run the script with these two options enabled
> (set to 1)?
>
> Should I enable both or just the "ENABLEAUTH"?
>
> Or can we (with your help, I hope) correct this issue?

As you have a backup, try creating the pam-config script I posted and 
then run 'pam-auth-update --package', this should get you the same pam 
setup as my member server.

Rowland