[Samba] cannot setup print in w2k on debian/samba/winwind/cups server
HANUISE ERIC
EH at sodexho.be
Thu Jun 13 03:31:03 GMT 2002
hi.
I am trying to get print working and have a hard time indeed...
My goal is to replace our nt4 print server with a linux/samba one as we have
problems serving printers and drivers to win2000 workstations (and I don't
want to set up a win2000 server for printing, and have the same problem
_again_ when switching to XP ;-)
The situation so far :
- Debian woody
- Samba 2.2.4-1
- Winbind 2.2.4-1
- CUPS 1.1.14
- Pulled the required files from the adobe generic PS driver and put the in
the right directory for my configuration. these files are root:root 0666
The server uses winbind to pull authentication from our NT domain PDC.
Auth works fine, the wbinfo queries all appear as normal.
Babbage:/etc/cups# wbinfo -a Administrator%-shht-
plaintext password authentication failed
error code was NT_STATUS_INVALID_PARAMETER (0xc000000d)
Could not authenticate user Administrator%-shht- with plaintext password
challenge/response password authentication succeeded
error code was NT_STATUS_OK (0x0)
Babbage:/etc/cups# wbinfo -t
Secret is good
Browsing files and folders works fine as well, so samba 'works' :)
Printing test pages from the server using CUPS's web interface
(http://babbage:631) outputs nice test pages on the printer, so CUPS seems
ok locally.
Whenever I try to cupsaddsmb -a (or cupsaddsmb -U
"SODEXHO.DOM\Administrator" fl2_inf_4050 , or cupsaddsmb -U
"SODEXHO.DOM\ROOT" fl2_inf_4050 or cupsaddsmb -U Administrator fl2_inf_4050
or cupsaddsmb -U root fl2_inf_4050) It asks a password, and refuses anything
I throw at it.
I even added a ROOT user to our NT domain, with the same password as teh
administrator (and this is also the same pass on the root account on the
linux server)
When I open \\babbage from a win2k workstation, I can see 'fl2_inf_4050' ,
the various shares, and 'Printers'.
If I try to add either \\babbage\fl2_inf_4050 or
\\babbage\printers\fl2_inf_4050 it says the server hasn't the right drivers
If I install the printer using local drivers, it installs OK, I can set
printer poperties and all. Then when I print from w2k (test pages or normal
prints) , I can see the jobs appearing in CUPS web interface as completed
jobs :
fl2_inf_4050-10 Test Page root 15k completed at
Thu Jun 13 11:08:59 2002 Restart Job
fl2_inf_4050-11 Test Page root 15k completed at
Thu Jun 13 11:11:48 2002 Restart Job
fl2_inf_4050-12 smbprn.000004.DVfRsB SODEXHO.DOM\EH 52k completed at
Thu Jun 13 11:16:53 2002 Restart Job
fl2_inf_4050-13 smbprn.000005.eERdJB SODEXHO.DOM\EH 37k completed at
Thu Jun 13 11:18:13 2002 Restart Job
fl2_inf_4050-14 smbprn.000006.h9qZnz SODEXHO.DOM\EH 44k completed at
Thu Jun 13 11:19:28 2002 Restart Job
fl2_inf_4050-15 smbprn.000007.dAtCRE SODEXHO.DOM\EH 52k completed at
Thu Jun 13 11:45:26 2002 Restart Job
fl2_inf_4050-16 smbprn.000008.s06Pqa SODEXHO.DOM\EH 52k completed at
Thu Jun 13 11:45:29 2002 Restart Job
fl2_inf_4050-17 smbprn.000009.pimxjb SODEXHO.DOM\EH 52k completed at
Thu Jun 13 11:45:31 2002 Restart Job
fl2_inf_4050-18 smbprn.000010.Odo1lR SODEXHO.DOM\EH 52k completed at
Thu Jun 13 11:45:32 2002 Restart Job
(the two first jobs are from cups' web interface 'test page' button, the
others are printed from the w2k workstation.)
only, they don't actually get printed.
Here are the config files for samba and cups :
----------------------------------------------------------------------
/etc/samba/smb.conf
----------------------------------------------------------------------
# Samba config file created using SWAT
# from 192.168.100.78 (192.168.100.78)
# Date: 2002/05/27 14:06:32
# Global parameters
[global]
workgroup = "SODEXHO.DOM"
netbios name = BABBAGE
server string = %h server (Samba %v)
security = DOMAIN
encrypt passwords = Yes
obey pam restrictions = Yes
password server = *
passwd program = /usr/bin/passwd %u
passwd chat = *Enter\snew\sUNIX\spassword:* %n\n
*Retype\snew\sUNIX\spassword:* %n\n .
password level = 8
username level = 8
syslog = 0
#log file = /var/log/samba/log.%m
max log size = 1000
load printers = yes
printing = cups
#printcap name = cups
printcap name = /etc/printcap.cups
preferred master = False
local master = No
domain master = False
dns proxy = No
wins server = 192.168.100.87
winbind uid = 10000-20000
winbind gid = 10000-20000
invalid users = root
create mask = 0600
security mask = 0666
directory mask = 0600
directory security mask = 0666
hide dot files = No
[Offers]
comment = repository
path = /home/offers-archive
read only = Yes
create mask = 0666
directory mask = 0666
directory security mask = 0666
hide dot files = No
browseable = Yes
[printers]
comment = All Printers
path = /tmp
browseable = yes
public = yes
guest ok = yes
printable = yes
printer admin = root, @"SODEXHO.DOM\Domain Admins"
[print$]
comment = printer drivers
path = /usr/share/cups/drivers
browseable = yes
guest ok = yes
read only = yes
write list = root
[cdrom]
comment = Samba server's CD-ROM
path = /cdrom
guest ok = Yes
locking = No
browseable = no
[c$]
comment = global admin share
path = /
invalid users =
valid users = @"SODEXHO.DOM\Domain Admins", "SODEXHO.DOM\BACKUP",
"SODEXHO.DOM\backupexec"
read only = No
create mask = 0666
browseable = No
locking = No
[Incoming]
comment = Incoming files (admins only)
path = /home/incoming
invalid users =
valid users = @"SODEXHO.DOM\Domain Admins"
read only = no
create mask = 0666
browseable = Yes
locking = no
----------------------------------------------------------------------
/etc/cups/cupsd.conf
----------------------------------------------------------------------
#
# "$Id: cupsd.conf.in,v 1.3 2002/02/12 18:47:11 mike Exp $"
#
# Sample configuration file for the Common UNIX Printing System (CUPS)
# scheduler.
#
# Copyright 1997-2002 by Easy Software Products, all rights reserved.
#
# These coded instructions, statements, and computer programs are the
# property of Easy Software Products and are protected by Federal
# copyright law. Distribution and use rights are outlined in the file
# "LICENSE.txt" which should have been included with this file. If this
# file is missing or damaged please contact Easy Software Products
# at:
#
# Attn: CUPS Licensing Information
# Easy Software Products
# 44141 Airport View Drive, Suite 204
# Hollywood, Maryland 20636-3111 USA
#
# Voice: (301) 373-9603
# EMail: cups-info at cups.org
# WWW: http://www.cups.org
#
########################################################################
# #
# This is the CUPS configuration file. If you are familiar with #
# Apache or any of the other popular web servers, we've followed the #
# same format. Any configuration variable used here has the same #
# semantics as the corresponding variable in Apache. If we need #
# different functionality then a different name is used to avoid #
# confusion... #
# #
########################################################################
########
######## Server Identity
########
#
# ServerName: the hostname of your server, as advertised to the world.
# By default CUPS will use the hostname of the system.
#
# To set the default server used by clients, see the client.conf file.
#
#ServerName myhost.domain.com
#
# ServerAdmin: the email address to send all complaints/problems to.
# By default CUPS will use "root at hostname".
#
ServerAdmin eh at sodexho.be
########
######## Server Options
########
#
# AccessLog: the access log file; if this does not start with a leading /
# then it is assumed to be relative to ServerRoot. By default set to
# "/var/log/cups/access_log"
#
# You can also use the special name "syslog" to send the output to the
# syslog file or daemon.
#
AccessLog /var/log/cups/access_log
#
# Classification: the classification level of the server. If set, this
# classification is displayed on all pages, and raw printing is disabled.
# The default is the empty string.
#
#Classification classified
#Classification confidential
#Classification secret
#Classification topsecret
#Classification unclassified
#
# ClassifyOverride: whether to allow users to override the classification
# on printouts. If enabled, users can limit banner pages to before or
# after the job, and can change the classification of a job, but cannot
# completely eliminate the classification or banners.
#
# The default is off.
#
#ClassifyOverride off
#
# DataDir: the root directory for the CUPS data files.
# By default "/usr/share/cups".
#
#DataDir /usr/share/cups
#
# DefaultCharset: the default character set to use. If not specified,
# defaults to "utf-8". Note that this can also be overridden in
# HTML documents...
#
#DefaultCharset utf-8
#
# DefaultLanguage: the default language if not specified by the browser.
# If not specified, the current locale is used.
#
#DefaultLanguage en
#
# DocumentRoot: the root directory for HTTP documents that are served.
# By default "/usr/share/cups/doc-root".
#
#DocumentRoot /usr/share/cups/doc-root
#
# ErrorLog: the error log file; if this does not start with a leading /
# then it is assumed to be relative to ServerRoot. By default set to
# "/var/log/cups/error_log"
#
# You can also use the special name "syslog" to send the output to the
# syslog file or daemon.
#
ErrorLog /var/log/cups/error_log
#
# FontPath: the path to locate all font files (currently only for
pstoraster)
# By default "/usr/share/cups/fonts".
#
#FontPath /usr/share/cups/fonts
#
# LogLevel: controls the number of messages logged to the ErrorLog
# file and can be one of the following:
#
# debug2 Log everything.
# debug Log almost everything.
# info Log all requests and state changes.
# warn Log errors and warnings.
# error Log only errors.
# none Log nothing.
#
LogLevel info
#
# MaxLogSize: controls the maximum size of each log file before they are
# rotated. Defaults to 1048576 (1MB). Set to 0 to disable log rotating.
#
#MaxLogSize 0
#
# PageLog: the page log file; if this does not start with a leading /
# then it is assumed to be relative to ServerRoot. By default set to
# "/var/log/cups/page_log"
#
# You can also use the special name "syslog" to send the output to the
# syslog file or daemon.
#
PageLog /var/log/cups/page_log
#
# PreserveJobHistory: whether or not to preserve the job history after a
# job is completed, cancelled, or stopped. Default is Yes.
#
#PreserveJobHistory Yes
#
# PreserveJobFiles: whether or not to preserve the job files after a
# job is completed, cancelled, or stopped. Default is No.
#
#PreserveJobFiles No
#
# AutoPurgeJobs: automatically purge jobs when not needed for quotas.
# Default is No.
#
#AutoPurgeJobs No
#
# MaxJobs: maximum number of jobs to keep in memory (active and completed.)
# Default is 500; the value 0 is used for no limit.
#
#MaxJobs 500
#
# Printcap: the name of the printcap file. Default is /etc/printcap.
# Leave blank to disable printcap file generation.
#
Printcap /etc/printcap.cups
#
# PrintcapFormat: the format of the printcap file, currently either
# BSD or Solaris. The default is "BSD".
#
#PrintcapFormat BSD
#PrintcapFormat Solaris
#
# PrintcapGUI: the name of the GUI options panel program to associate
# with print queues under IRIX. The default is "/usr/bin/glpoptions"
# from ESP Print Pro.
#
# This option is only used under IRIX; the options panel program
# must accept the "-d printer" and "-o options" options and write
# the selected printer options back to stdout on completion.
#
#PrintcapGUI /usr/bin/glpoptions
#
# RequestRoot: the directory where request files are stored.
# By default "/var/spool/cups".
#
#RequestRoot /var/spool/cups
#
# RemoteRoot: the name of the user assigned to unauthenticated accesses
# from remote systems. By default "remroot".
#
#RemoteRoot remroot
#
# ServerBin: the root directory for the scheduler executables.
# By default "/usr/lib/cups".
#
#ServerBin /usr/lib/cups
#
# ServerRoot: the root directory for the scheduler.
# By default "/etc/cups".
#
#ServerRoot /etc/cups
########
######## Encryption Support
########
#
# ServerCertificate: the file to read containing the server's certificate.
# Defaults to "/etc/cups/ssl/server.crt".
#
#ServerCertificate /etc/cups/ssl/server.crt
#
# ServerKey: the file to read containing the server's key.
# Defaults to "/etc/cups/ssl/server.key".
#
#ServerKey /etc/cups/ssl/server.key
########
######## Filter Options
########
#
# User/Group: the user and group the server runs under. Normally this
# must be lp and sys, however you can configure things for another
# user or group as needed.
#
# Note: the server must be run initially as root to support the
# default IPP port of 631. It changes users whenever an external
# program is run, or if the RunAsUser directive is specified...
#
User lp
Group sys
#
# RIPCache: the amount of memory that each RIP should use to cache
# bitmaps. The value can be any real number followed by "k" for
# kilobytes, "m" for megabytes, "g" for gigabytes, or "t" for tiles
# (1 tile = 256x256 pixels.) Defaults to "8m" (8 megabytes).
#
#RIPCache 8m
#
# TempDir: the directory to put temporary files in. This directory must be
# writable by the user defined above! Defaults to "/var/spool/cups/tmp" or
# the value of the TMPDIR environment variable.
#
#TempDir /var/spool/cups/tmp
#
# FilterLimit: sets the maximum cost of all job filters that can be run
# at the same time. A limit of 0 means no limit. A typical job may need
# a filter limit of at least 200; limits less than the minimum required
# by a job force a single job to be printed at any time.
#
# The default limit is 0 (unlimited).
#
#FilterLimit 0
########
######## Network Options
########
#
# Ports/addresses that we listen to. The default port 631 is reserved
# for the Internet Printing Protocol (IPP) and is what we use here.
#
# You can have multiple Port/Listen lines to listen to more than one
# port or address, or to restrict access:
#
# Port 80
# Port 631
# Listen hostname
# Listen hostname:80
# Listen hostname:631
# Listen 1.2.3.4
# Listen 1.2.3.4:631
#
# NOTE: Unfortunately, most web browsers don't support TLS or HTTP Upgrades
# for encryption. If you want to support web-based encryption you'll
# probably need to listen on port 443 (the "https" port...)
#
#Port 80
#Port 443
Port 631
#
# HostNameLookups: whether or not to do lookups on IP addresses to get a
# fully-qualified hostname. This defaults to Off for performance reasons...
#
#HostNameLookups On
#
# KeepAlive: whether or not to support the Keep-Alive connection
# option. Default is on.
#
#KeepAlive On
#
# KeepAliveTimeout: the timeout before Keep-Alive connections are
# automatically closed. Default is 60 seconds.
#
#KeepAliveTimeout 60
#
# MaxClients: controls the maximum number of simultaneous clients that
# will be handled. Defaults to 100.
#
#MaxClients 100
#
# MaxRequestSize: controls the maximum size of HTTP requests and print
files.
# Set to 0 to disable this feature (defaults to 0.)
#
#MaxRequestSize 0
#
# Timeout: the timeout before requests time out. Default is 300 seconds.
#
#Timeout 300
########
######## Browsing Options
########
#
# Browsing: whether or not to broadcast and/or listen for CUPS printer
# information on the network. Enabled by default.
#
Browsing Off
#
# BrowseProtocols: which protocols to use for browsing. Can be
# any of the following separated by whitespace and/or commas:
#
# all - Use all supported protocols.
# cups - Use the CUPS browse protocol.
# slp - Use the SLPv2 protocol.
#
# The default is "cups".
#
# NOTE: If you choose to use SLPv2, it is *strongly* recommended that
# you have at least one SLP Directory Agent (DA) on your
# network. Otherwise, browse updates can take several seconds,
# during which the scheduler will not response to client
# requests.
#
#BrowseProtocols cups
#
# BrowseAddress: specifies a broadcast address to be used. By
# default browsing information is not sent!
#
# Note: HP-UX does not properly handle broadcast unless you have a
# Class A, B, C, or D netmask (i.e. no CIDR support).
#
# Note: Using the "global" broadcast address (255.255.255.255) will
# activate a Linux demand-dial link with the default configuration.
# If you have a LAN as well as the dial-up link, use the LAN's
# broadcast address.
#
#BrowseAddress x.y.z.255
#BrowseAddress x.y.255.255
#BrowseAddress x.255.255.255
#BrowseAddress 255.255.255.255
#
# BrowseShortNames: whether or not to use "short" names for remote printers
# when possible (e.g. "printer" instead of "printer at host".) Enabled by
# default.
#
#BrowseShortNames Yes
#
# BrowseAllow: specifies an address mask to allow for incoming browser
# packets. The default is to allow packets from all addresses.
#
# BrowseDeny: specifies an address mask to deny for incoming browser
# packets. The default is to deny packets from no addresses.
#
# Both "BrowseAllow" and "BrowseDeny" accept the following notations for
# addresses:
#
# All
# None
# *.domain.com
# .domain.com
# host.domain.com
# nnn.*
# nnn.nnn.*
# nnn.nnn.nnn.*
# nnn.nnn.nnn.nnn
# nnn.nnn.nnn.nnn/mm
# nnn.nnn.nnn.nnn/mmm.mmm.mmm.mmm
#
# The hostname/domainname restrictions only work if you have turned hostname
# lookups on!
#
#BrowseAllow address
#BrowseDeny address
#
# BrowseInterval: the time between browsing updates in seconds. Default
# is 30 seconds.
#
# Note that browsing information is sent whenever a printer's state changes
# as well, so this represents the maximum time between updates.
#
# Set this to 0 to disable outgoing broadcasts so your local printers are
# not advertised but you can still see printers on other hosts.
#
#BrowseInterval 30
#
# BrowseOrder: specifies the order of BrowseAllow/BrowseDeny comparisons.
#
#BrowseOrder allow,deny
#BrowseOrder deny,allow
#
# BrowsePoll: poll the named server(s) for printers
#
#BrowsePoll address:port
#
# BrowsePort: the port used for UDP broadcasts. By default this is
# the IPP port; if you change this you need to do it on all servers.
# Only one BrowsePort is recognized.
#
#BrowsePort 631
#
# BrowseRelay: relay browser packets from one address/network to another.
#
#BrowseRelay source-address destination-address
#
# BrowseTimeout: the timeout for network printers - if we don't
# get an update within this time the printer will be removed
# from the printer list. This number definitely should not be
# less the BrowseInterval value for obvious reasons. Defaults
# to 300 seconds.
#
#BrowseTimeout 300
#
# ImplicitClasses: whether or not to use implicit classes.
#
# Printer classes can be specified explicitly in the classes.conf
# file, implicitly based upon the printers available on the LAN, or
# both.
#
# When ImplicitClasses is On, printers on the LAN with the same name
# (e.g. Acme-LaserPrint-1000) will be put into a class with the same
# name. This allows you to setup multiple redundant queues on a LAN
# without a lot of administrative difficulties. If a user sends a
# job to Acme-LaserPrint-1000, the job will go to the first available
# queue.
#
# Enabled by default.
#
#ImplicitClasses On
#
# ImplicitAnyClasses: whether or not to create "AnyPrinter" implicit
# classes.
#
# When ImplicitAnyClasses is On and a local queue of the same name
# exists, e.g. "printer", "printer at server1", "printer at server1", then
# an implicit class called "Anyprinter" is created instead.
#
# When ImplicitAnyClasses is Off, implicit classes are not created
# when there is a local queue of the same name.
#
# Disabled by default.
#
#ImplicitAnyCLasses Off
#
# HideImplicitMembers: whether or not to show the members of an
# implicit class.
#
# When HideImplicitMembers is On, any remote printers that are
# part of an implicit class are hidden from the user, who will
# then only see a single queue even though many queues will be
# supporting the implicit class.
#
# Enabled by default.
#
#HideImplicitMembers On
########
######## Security Options
########
#
# SystemGroup: the group name for "System" (printer administration)
# access. The default varies depending on the operating system, but
# will be "sys", "system", or "root" (checked for in that order.)
#
SystemGroup lpadmin
#
# Access permissions for each directory served by the scheduler.
# Locations are relative to DocumentRoot...
#
# AuthType: the authorization to use:
#
# None - Perform no authentication
# Basic - Perform authentication using the HTTP Basic method.
# Digest - Perform authentication using the HTTP Digest method.
#
# (Note: local certificate authentication can be substituted by
# the client for Basic or Digest when connecting to the
# localhost interface)
#
# AuthClass: the authorization class; currently only "Anonymous", "User",
# "System" (valid user belonging to group SystemGroup), and "Group"
# (valid user belonging to the specified group) are supported.
#
# AuthGroupName: the group name for "Group" authorization.
#
# Order: the order of Allow/Deny processing.
#
# Allow: allows access from the specified hostname, domain, IP address, or
# network.
#
# Deny: denies access from the specified hostname, domain, IP address, or
# network.
#
# Both "Allow" and "Deny" accept the following notations for addresses:
#
# All
# None
# *.domain.com
# .domain.com
# host.domain.com
# nnn.*
# nnn.nnn.*
# nnn.nnn.nnn.*
# nnn.nnn.nnn.nnn
# nnn.nnn.nnn.nnn/mm
# nnn.nnn.nnn.nnn/mmm.mmm.mmm.mmm
#
# The host and domain address require that you enable hostname lookups
# with "HostNameLookups On" above.
#
# Encryption: whether or not to use encryption; this depends on having
# the OpenSSL library linked into the CUPS library and scheduler.
#
# Possible values:
#
# Always - Always use encryption (SSL)
# Never - Never use encryption
# Required - Use TLS encryption upgrade
# IfRequested - Use encryption if the server requests it
#
# The default value is "IfRequested".
#
<Location />
Order Deny,Allow
Deny From All
Allow From 127.0.0.1
Allow from 192.168.100.0/24
</Location>
#<Location /classes>
#
# You may wish to limit access to printers and classes, either with Allow
# and Deny lines, or by requiring a username and password.
#
#</Location>
#<Location /classes/name>
#
# You may wish to limit access to printers and classes, either with Allow
# and Deny lines, or by requiring a username and password.
#
#</Location>
#<Location /printers>
#
# You may wish to limit access to printers and classes, either with Allow
# and Deny lines, or by requiring a username and password.
#
#</Location>
#<Location /printers/name>
#
# You may wish to limit access to printers and classes, either with Allow
# and Deny lines, or by requiring a username and password.
#
## Anonymous access (default)
#AuthType None
## Require a username and password (Basic authentication)
#AuthType Basic
#AuthClass User
## Require a username and password (Digest/MD5 authentication)
#AuthType Digest
#AuthClass User
## Restrict access to local domain
#Order Deny,Allow
#Deny From All
#Allow From .mydomain.com
#</Location>
<Location /admin>
#
# You definitely will want to limit access to the administration functions.
# The default configuration requires a local connection from a user who
# is a member of the system group to do any admin tasks. You can change
# the group name using the SystemGroup directive.
#
AuthType Basic
AuthClass System
## Restrict access to local domain
Order Deny,Allow
Deny From All
Allow From 127.0.0.1
Allow from 192.168.100.0/24
#Encryption Required
</Location>
#
# End of "$Id: cupsd.conf.in,v 1.3 2002/02/12 18:47:11 mike Exp $".
#
----------------------------------------------------------------------
If it works, don't fix it.
----------------------------------------------------------------------
Eric Hanuise - Systems/Network Administrator
Sodexho belgium - Rue charles lemaire,1 - 1160 Brussels
T. 02 679 11 86 - mobile 0495 58 01 74
----------------------------------------------------------------------
More information about the samba
mailing list