[WHATSNEW] Samba AD with MIT Kerberos + Version change

[L.P.H. van Belle]

Ok thanks, i'll report back later, i'll setup some things up. 

Just one question the gnutls, is needed for samba or mit, because maybe i need to change there someing in the MIT builds.

Greetz, 

Louis



> -----Oorspronkelijk bericht-----
> Van: Rowland Penny [mailto:rpenny at samba.org] 
> Verzonden: donderdag 4 mei 2017 11:11
> Aan: L.P.H. van Belle
> CC: samba-technical at lists.samba.org 
> Onderwerp: Re: [WHATSNEW] Samba AD with MIT Kerberos + Version change
> 
> On Thu, 4 May 2017 10:44:03 +0200
> L.P.H. van Belle <belle at bazuin.nl> wrote:
> 
> > Hai Rowland,
> > 
> > I'll setup a jessie and try a provsioning test also. 
> > I pretty new with git, so a bit of guidance maybe needed. 
> > 
> > I checkout, https://git.samba.org/ , lots of options.
> > Just pull?  https://git.samba.org/samba.git
> > 
> > 
> 
> You will have to use stretch, you need a later version of 
> gnutls the the one on jessie.
> 
> I installed these:
> 
>   apt-get install build-essential libacl1-dev libattr1-dev 
> libblkid-dev
>   libreadline-dev python-dev libpam0g-dev python-dnspython gdb
>   pkg-config libpopt-dev libldap2-dev dnsutils libbsd-dev attr
>   docbook-xsl libcups2-dev acl libssl-dev xsltproc krb5-config
>   libpam-krb5 libgnutls28-dev ntp libverto1 libverto-libev1 comerr-dev
>   libev4 git
> 
> Then your packages:
> 
> dpkg -i krb5-kdc_1.15.1-1+mnu1_amd64.deb 
> krb5-locales_1.15.1-1+mnu1_all.deb
> krb5-multidev_1.15.1-1+mnu1_amd64.deb 
> krb5-user_1.15.1-1+mnu1_amd64.deb 
> libgssapi-krb5-2_1.15.1-1+mnu1_amd64.deb
> libkrb5-3_1.15.1-1+mnu1_amd64.deb libkrb5-dev_1.15.1-1+mnu1_amd64.deb
> libk5crypto3_1.15.1-1+mnu1_amd64.deb
> libkrb5support0_1.15.1-1+mnu1_amd64.deb
> libgssrpc4_1.15.1-1+mnu1_amd64.deb
> libkadm5srv-mit11_1.15.1-1+mnu1_amd64.deb
> libkadm5clnt-mit11_1.15.1-1+mnu1_amd64.deb
> krb5-admin-server_1.15.1-1+mnu1_amd64.deb
> krb5-k5tls_1.15.1-1+mnu1_amd64.deb krb5-pkinit_1.15.1-1+mnu1_amd64.deb
> libkdb5-8_1.15.1-1+mnu1_amd64.deb
> 
> Not sure if you need all of them, but better safe than sorry ;-)
> 
> Then pull from git:
> 
> cd /usr/src
> mkdir git
> cd git
> git clone git://git.samba.org/samba.git samba-master cd samba-master
> 
> Then change a couple of files:
> 
> nano python/wscript
> 
> Change (line 37):
> 
> paths = [ "/var/kerberos/krb5kdc", "/var/lib/kerberos/krb5kdc" ]
> 
> To:
> 
> paths = [ "/var/kerberos/krb5kdc", 
> "/var/lib/kerberos/krb5kdc", "/etc/krb5kdc" ]
> 
> nano python/samba/provision/kerberos.py
> 
> Change (line 24):
> 
> from samba import _glue
> 
> To:
> 
> from samba import is_heimdal_built
> 
> Change (line 29):
> if _glue.is_heimdal_built:
> 
> To:
> 
> if is_heimdal_built:
> 
> Then compile Samba:
> 
> ./configure --with-system-mitkrb5
> make
> make install
> 
> This should give you Samba in /usr/local/samba
> 
> Rowland
> 
>