[[PATCH v1] 18/37] [CIFS] SMBD: Implement API for upper layer to send data

[Long Li]

> -----Original Message-----
> From: Tom Talpey
> Sent: Monday, August 14, 2017 1:44 PM
> To: Long Li <longli at microsoft.com>; Steve French <sfrench at samba.org>;
> linux-cifs at vger.kernel.org; samba-technical at lists.samba.org; linux-
> kernel at vger.kernel.org; linux-rdma at vger.kernel.org
> Subject: RE: [[PATCH v1] 18/37] [CIFS] SMBD: Implement API for upper layer
> to send data
> 
> > -----Original Message-----
> > From: linux-cifs-owner at vger.kernel.org [mailto:linux-cifs-
> > owner at vger.kernel.org] On Behalf Of Long Li
> > Sent: Wednesday, August 2, 2017 4:10 PM
> > To: Steve French <sfrench at samba.org>; linux-cifs at vger.kernel.org;
> > samba- technical at lists.samba.org; linux-kernel at vger.kernel.org
> > Cc: Long Li <longli at microsoft.com>
> > Subject: [[PATCH v1] 18/37] [CIFS] SMBD: Implement API for upper layer
> > to send data
> >
> > +/*
> > + * Write data to transport
> > + * Each rqst is transported as a SMBDirect payload
> > + * rqst: the data to write
> > + * return value: 0 if successfully write, otherwise error code  */
> > +int cifs_rdma_write(struct cifs_rdma_info *info, struct smb_rqst
> > +*rqst) {
> 
> !!!
> This is a VERY confusing name. It is not sending an RDMA Write, which will
> confuse any RDMA-enlightened reader. It's performing an RDMA Send, so
> that name is perhaps one possibility.

I have fixed that in v3.

> 
> > +       if (info->transport_status != CIFS_RDMA_CONNECTED) {
> > +               log_cifs_write("disconnected returning -EIO\n");
> > +               return -EIO;
> > +       }
> 
> Isn't this optimizing the error case? There's no guarantee it's still connected
> by the time the following request construction occurs. Why not just proceed
> without the check?

I rearranged the shutdown logic in v3. Checking for transport status is still needed, but it checks after checking for other counters on pending activities.

For example, on sending code:

info->smbd_send_pending++;
if (info->transport_status != SMBD_CONNECTED) {
        info->smbd_send_pending--;
        wake_up(&info->wait_smbd_send_pending);        
}

On transport shutdown code:

        info->transport_status = SMBD_DISCONNECTING;
.......
.......
.......
        log_rdma_event(INFO, "wait for all send to finish\n");
        wait_event(info->wait_smbd_send_pending,
                info->smbd_send_pending == 0);

It guarantees no sending code can enter transport after shutdown is finished. Shutdown is running on a separate work queue, so it is needed.

> 
> > +       /* Strip the first 4 bytes MS-SMB2 section 2.1
> > +        * they are used only for TCP transport */
> > +       iov[0].iov_base = (char*)rqst->rq_iov[0].iov_base + 4;
> > +       iov[0].iov_len = rqst->rq_iov[0].iov_len - 4;
> > +       buflen += iov[0].iov_len;
> 
> Ok, that layering choice in the cifs.ko client code needs to be corrected. After
> all, it will need to be RDMA-aware to build the SMB3 read/write channel
> structures.
> And, the code in cifs_post_send_data() is allocating and building a structure
> that could have been accounted for much earlier, avoiding the extra
> overhead.
> 
> That change could happen later, the hack is mostly ok for now. But
> something needs to be said in a comment.
> 
> Tom.