[clug] no reception with a new Twinhan USB2.0 DVB-T receiver
Leo Kliger
lkliger at bigpond.net.au
Tue Aug 15 12:22:16 GMT 2006
Hi,
I just got a new Twinhan USB2.0 DVB-T receiver and don't seem to be
getting any effective reception through it - while my Avermedia DVB-T
771 cards happily receive through the very same cable.
Is anybody using these USB devices with success?
If so I was hoping to compare kernel revisions and lspci, lsmod dmesg
output.
Mine are attached below.
BTW - I downloaded "dvb-usb-vp7045-01.fw" from
http://www.linuxtv.org/download/firmware/ and place the file
into /lib/firmware
Thanks,
Leo
# uname -a
Linux borgcube9 2.6.17-1.2174_FC5 #1 SMP Tue Aug 8 15:30:44 EDT 2006
x86_64 x86_64 x86_64 GNU/Linux
# lspci
00:00.0 Host bridge: Intel Corporation E7230 Memory Controller Hub (rev
81)
00:01.0 PCI bridge: Intel Corporation E7230 PCI Express Root Port (rev
81)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 1 (rev 01)
00:1c.4 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI
Express Port 5 (rev 01)
00:1c.5 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI
Express Port 6 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
#1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
#2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
#3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
#4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI
Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC
Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE
Controller (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family)
Serial ATA Storage Controllers cc=IDE (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller
(rev 01)
01:00.0 PCI bridge: Intel Corporation 6700PXH PCI Express-to-PCI Bridge
A (rev 09)
01:00.1 PIC: Intel Corporation 6700/6702PXH I/OxAPIC Interrupt
Controller A (rev 09)
01:00.2 PCI bridge: Intel Corporation 6700PXH PCI Express-to-PCI Bridge
B (rev 09)
01:00.3 PIC: Intel Corporation 6700PXH I/OxAPIC Interrupt Controller B
(rev 09)
04:00.0 PCI bridge: Intel Corporation 41210 [Lanai] Serial to Parallel
PCI Bridge (A-Segment Bridge) (rev 09)
04:00.2 PCI bridge: Intel Corporation 41210 [Lanai] Serial to Parallel
PCI Bridge (B-Segment Bridge) (rev 09)
05:0c.0 RAID bus controller: 3ware Inc 9550SX SATA-RAID
07:00.0 Ethernet controller: Intel Corporation 82573E Gigabit Ethernet
Controller (Copper) (rev 03)
08:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet
Controller
0a:04.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
# lsmod
Module Size Used by
i2c_algo_bit 42953 0
nfsd 328969 17
exportfs 39745 1 nfsd
lockd 112465 2 nfsd
nfs_acl 37185 1 nfsd
autofs4 60233 1
hidp 85057 2
rfcomm 112481 0
l2cap 94017 10 hidp,rfcomm
bluetooth 125637 5 hidp,rfcomm,l2cap
sunrpc 230153 12 nfsd,lockd,nfs_acl
acpi_cpufreq 43325 0
sr_mod 53989 0
jfs 220881 1
dm_mirror 59457 0
dm_mod 107537 1 dm_mirror
video 54345 0
button 41569 0
battery 44873 0
acpi_memhotplug 39361 0
ac 39241 0
dvb_usb_vp7045 44869 0
dvb_usb 56521 1 dvb_usb_vp7045
dvb_core 130800 1 dvb_usb
dvb_pll 47429 1 dvb_usb
usb_storage 116129 0
ipv6 442785 22
lp 49425 0
parport_pc 66153 0
parport 80461 2 lp,parport_pc
e1000 160697 0
sg 74089 0
serio_raw 42053 0
ehci_hcd 71501 0
floppy 105417 0
uhci_hcd 61529 0
i2c_i801 43477 0
i2c_core 60993 3 i2c_algo_bit,dvb_usb,i2c_i801
ext3 181841 2
jbd 100585 1 ext3
ata_piix 46789 3
libata 113113 1 ata_piix
3w_9xxx 69061 1
sd_mod 55745 6
scsi_mod 198033 6
sr_mod,usb_storage,sg,libata,3w_9xxx,sd_mod
# dmesg
Bootdata ok (command line is ro root=LABEL=/ rhgb quiet)
Linux version 2.6.17-1.2174_FC5
(brewbuilder at hs20-bc2-3.build.redhat.com) (gcc version 4.1.1 20060525
(Red Hat 4.1.1-1)) #1 SMP Tue Aug 8 15:30:44 EDT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009d800 (usable)
BIOS-e820: 000000000009d800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fee0000 (usable)
BIOS-e820: 000000007fee0000 - 000000007fee9000 (ACPI data)
BIOS-e820: 000000007fee9000 - 000000007ff00000 (ACPI NVS)
BIOS-e820: 000000007ff00000 - 0000000080000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
DMI present.
ACPI: RSDP (v000 PTLTD ) @
0x00000000000f5ed0
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @
0x000000007fee3be9
ACPI: FADT (v001 INTEL 0x06040000 PTL 0x00000003) @
0x000000007fee8ea8
ACPI: MCFG (v001 PTLTD MCFG 0x06040000 LTP 0x00000000) @
0x000000007fee8f1c
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @
0x000000007fee8f58
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @
0x000000007fee8fd8
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20030224) @
0x000000007fee3c21
ACPI: DSDT (v001 INTEL GLENWOOD 0x06040000 MSFT 0x0100000e) @
0x0000000000000000
No NUMA configuration found
Faking a node at 0000000000000000-000000007fee0000
Bootmem setup node 0 0000000000000000-000000007fee0000
On node 0 totalpages: 514162
DMA zone: 2381 pages, LIFO batch:0
DMA32 zone: 511781 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:6 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:6 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfec80000] gsi_base[24])
IOAPIC[1]: apic_id 3, version 32, address 0xfec80000, GSI 24-47
ACPI: IOAPIC (id[0x04] address[0xfec80400] gsi_base[48])
IOAPIC[2]: apic_id 4, version 32, address 0xfec80400, GSI 48-71
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000)
Checking aperture...
SMP: Allowing 2 CPUs, 0 hotplug CPUs
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
time.c: Detected 2992.603 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Memory: 2052184k/2096000k available (2387k kernel code, 43420k reserved,
1700k data, 200k init)
Calibrating delay using timer specific routine.. 5990.63 BogoMIPS
(lpj=11981275)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring handled by SMI
Using local APIC timer interrupts.
result 12469113
Detected 12.469 MHz APIC timer.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 89071.64 BogoMIPS
(lpj=178143297)
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM1)
Intel(R) Pentium(R) D CPU 3.00GHz stepping 02
Brought up 2 CPUs
testing NMI watchdog ... OK.
migration_cost=1321
checking if image is initramfs... it is
Freeing initrd memory: 1108k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: PXH quirk detected, disabling MSI for SHPC device
PCI: PXH quirk detected, disabling MSI for SHPC device
Boot video device is 0000:0a:04.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.DEV1.PXHA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.DEV1.PXHB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP5._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP6._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 10 11 14 15) *5
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:01:00.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:01:00.2
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: ea100000-ea1fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:04:00.0
IO window: 7000-7fff
MEM window: ea200000-ea2fffff
PREFETCH window: ee000000-efffffff
PCI: Bridge: 0000:04:00.2
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.0
IO window: 7000-7fff
MEM window: ea200000-ea2fffff
PREFETCH window: ee000000-efffffff
PCI: Bridge: 0000:00:1c.4
IO window: 8000-8fff
MEM window: ea300000-ea3fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.5
IO window: 9000-9fff
MEM window: ea400000-ea4fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: a000-afff
MEM window: ea500000-ebffffff
PREFETCH window: 88000000-880fffff
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:01:00.0 to 64
PCI: Setting latency timer of device 0000:01:00.2 to 64
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Setting latency timer of device 0000:04:00.0 to 64
PCI: Setting latency timer of device 0000:04:00.2 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.4 to 64
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.5 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 131072 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 9, 2097152 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag at 0x37 set to 0x1
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1155623353.448:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key D4AD441F6DB3F282
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.4:pcie00]
Allocate Port Service[0000:00:1c.4:pcie02]
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.5 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.5:pcie00]
Allocate Port Service[0000:00:1c.5:pcie02]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Processor [CPU1] (supports 8 throttling states)
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
GSI 18 sharing vector 0xE1 and IRQ 18
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 225
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x64d0-0x64d7, BIOS settings: hda:pio, hdb:pio
Probing IDE interface ide0...
Probing IDE interface ide0...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI wakeup devices:
PXHA PXHB EXP1 EXP4 EXP5 EXP6 PCIB KBC0 MSE0 USB1 USB2 USB3 USB4 EUSB
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 200k freed
Write protecting the kernel read-only data: 919k
input: AT Translated Set 2 keyboard as /class/input/input0
SCSI subsystem initialized
3ware 9000 Storage Controller device driver for Linux v2.26.02.007.
ACPI: PCI Interrupt 0000:05:0c.0[A] -> GSI 16 (level, low) -> IRQ 169
3w-9xxx: scsi0: AEN: INFO (0x04:0x0053): Battery capacity test is
overdue:.
scsi0 : 3ware 9000 Storage Controller
3w-9xxx: scsi0: Found a 3ware 9000 Storage Controller at 0xea200000,
IRQ: 169.
3w-9xxx: scsi0: Firmware FE9X 3.04.00.005, BIOS BE9X 3.04.00.002, Ports:
8.
Vendor: AMCC Model: 9590SE-8ML DISK Rev: 3.04
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sda: 2929625088 512-byte hdwr sectors (1499968 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
SCSI device sda: drive cache: write back, no read (daft)
SCSI device sda: 2929625088 512-byte hdwr sectors (1499968 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
SCSI device sda: drive cache: write back, no read (daft)
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
libata version 1.20 loaded.
ata_piix 0000:00:1f.2: version 1.05
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
GSI 19 sharing vector 0xE9 and IRQ 19
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x6898 ctl 0x687E bmdma 0x6880 irq 233
ata2: SATA max UDMA/133 cmd 0x6890 ctl 0x687A bmdma 0x6888 irq 233
input: ImExPS/2 Generic Explorer Mouse as /class/input/input1
ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023
88:207f
ata1: dev 0 ATA-7, max UDMA/133, 781422768 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi1 : ata_piix
ata2: SATA port has no device.
scsi2 : ata_piix
Vendor: ATA Model: WDC WD4000KD-00N Rev: 01.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 781422768 512-byte hdwr sectors (400088 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 781422768 512-byte hdwr sectors (400088 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb3
sd 1:0:0:0: Attached scsi disk sdb
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1155623357.376:2): selinux=0 auid=4294967295
USB Universal Host Controller Interface driver v3.0
GSI 20 sharing vector 0x32 and IRQ 20
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 50, io base 0x000064e0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Floppy drive(s): fd0 is 1.44M
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 233, io base 0x00006800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
FDC 0 is a post-1991 82077
hw_random: RNG not detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 225, io base 0x00006820
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
Intel(R) PRO/1000 Network Driver - version 7.0.33-k2-NAPI
Copyright (c) 1999-2005 Intel Corporation.
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 169, io base 0x00006840
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: new full speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 50, io mem 0xea000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:07:00.0 to 64
e1000: 0000:07:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1)
00:30:48:88:95:30
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:08:00.0 to 64
e1000: 0000:08:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1)
00:30:48:88:95:31
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
usb 1-2: device not accepting address 2, error -71
lp: driver loaded but no devices found
hub 4-0:1.0: over-current change on port 1
hub 4-0:1.0: over-current change on port 2
usb 5-2: new high speed USB device using ehci_hcd and address 2
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
usb 5-2: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
usb 5-3: new high speed USB device using ehci_hcd and address 3
usb 5-3: configuration #1 chosen from 1 choice
usb 5-4: new high speed USB device using ehci_hcd and address 4
usb 5-4: configuration #1 chosen from 1 choice
usb 5-5: new high speed USB device using ehci_hcd and address 5
usb 5-5: configuration #1 chosen from 1 choice
usb 5-6: new high speed USB device using ehci_hcd and address 6
usb 5-6: configuration #1 chosen from 1 choice
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
dvb-usb: found a 'DigitalNow TinyUSB 2 DVB-t Receiver' in cold state,
will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-vp7045-01.fw'
dvb-usb: found a 'DigitalNow TinyUSB 2 DVB-t Receiver' in cold state,
will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-vp7045-01.fw'
dvb-usb: found a 'DigitalNow TinyUSB 2 DVB-t Receiver' in cold state,
will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-vp7045-01.fw'
dvb-usb: found a 'DigitalNow TinyUSB 2 DVB-t Receiver' in cold state,
will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-vp7045-01.fw'
usb 5-3: USB disconnect, address 3
dvb-usb: generic DVB-USB module successfully deinitialized and
disconnected.
usbcore: registered new driver dvb_usb_vp7045
usb 5-4: USB disconnect, address 4
dvb-usb: generic DVB-USB module successfully deinitialized and
disconnected.
usb 5-5: USB disconnect, address 5
dvb-usb: generic DVB-USB module successfully deinitialized and
disconnected.
usb 5-6: USB disconnect, address 6
dvb-usb: generic DVB-USB module successfully deinitialized and
disconnected.
usb 5-3: new high speed USB device using ehci_hcd and address 7
usb 5-3: configuration #1 chosen from 1 choice
dvb-usb: found a 'Twinhan USB2.0 DVB-T receiver (TwinhanDTV
Alpha/MagicBox II)' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software
demuxer.
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
DVB: registering new adapter (Twinhan USB2.0 DVB-T receiver (TwinhanDTV
Alpha/MagicBox II)).
dvb-usb: MAC address: 08:ca:1a:af:1d:ff
DVB: registering frontend 0 (Twinhan VP7045/46 USB DVB-T)...
input: IR-receiver inside an USB DVB receiver as /class/input/input2
dvb-usb: schedule remote query interval to 400 msecs.
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel at redhat.com
dvb-usb: Twinhan USB2.0 DVB-T receiver (TwinhanDTV Alpha/MagicBox II)
successfully initialized and connected.
usb 5-4: new high speed USB device using ehci_hcd and address 8
EXT3 FS on sdb2, internal journal
usb 5-4: configuration #1 chosen from 1 choice
dvb-usb: found a 'Twinhan USB2.0 DVB-T receiver (TwinhanDTV
Alpha/MagicBox II)' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software
demuxer.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
JFS: nTxBlock = 8192, nTxLock = 65536
DVB: registering new adapter (Twinhan USB2.0 DVB-T receiver (TwinhanDTV
Alpha/MagicBox II)).
dvb-usb: MAC address: 08:ca:1a:af:5a:ff
DVB: registering frontend 1 (Twinhan VP7045/46 USB DVB-T)...
input: IR-receiver inside an USB DVB receiver as /class/input/input3
dvb-usb: schedule remote query interval to 400 msecs.
dvb-usb: Twinhan USB2.0 DVB-T receiver (TwinhanDTV Alpha/MagicBox II)
successfully initialized and connected.
usb 5-5: new high speed USB device using ehci_hcd and address 9
Adding 2048276k swap on /dev/sdb3. Priority:-1 extents:1
across:2048276k
usb 5-5: configuration #1 chosen from 1 choice
dvb-usb: found a 'Twinhan USB2.0 DVB-T receiver (TwinhanDTV
Alpha/MagicBox II)' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software
demuxer.
DVB: registering new adapter (Twinhan USB2.0 DVB-T receiver (TwinhanDTV
Alpha/MagicBox II)).
dvb-usb: MAC address: 08:ca:1a:af:46:ff
DVB: registering frontend 2 (Twinhan VP7045/46 USB DVB-T)...
input: IR-receiver inside an USB DVB receiver as /class/input/input4
dvb-usb: schedule remote query interval to 400 msecs.
dvb-usb: Twinhan USB2.0 DVB-T receiver (TwinhanDTV Alpha/MagicBox II)
successfully initialized and connected.
usb 5-6: new high speed USB device using ehci_hcd and address 10
usb 5-6: configuration #1 chosen from 1 choice
dvb-usb: found a 'Twinhan USB2.0 DVB-T receiver (TwinhanDTV
Alpha/MagicBox II)' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software
demuxer.
DVB: registering new adapter (Twinhan USB2.0 DVB-T receiver (TwinhanDTV
Alpha/MagicBox II)).
dvb-usb: MAC address: 08:ca:1a:af:08:ff
DVB: registering frontend 3 (Twinhan VP7045/46 USB DVB-T)...
input: IR-receiver inside an USB DVB receiver as /class/input/input5
dvb-usb: schedule remote query interval to 400 msecs.
dvb-usb: Twinhan USB2.0 DVB-T receiver (TwinhanDTV Alpha/MagicBox II)
successfully initialized and connected.
Vendor: PIONEER Model: DVD-RW DVR-110D Rev: 1.08
Type: CD-ROM ANSI SCSI revision: 00
3:0:0:0: Attached scsi generic sg2 type 5
usb-storage: device scan complete
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
ADDRCONF(NETDEV_UP): eth0: link is not ready
e1000: eth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Full Duplex
e1000: eth0: e1000_watchdog_task: 10/100 speed: disabling TSO
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.7
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
eth0: no IPv6 routers present
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery
directory
NFSD: unable to find recovery directory /var/lib/nfs/v4recovery
NFSD: starting 90-second grace period
usb 5-2: USB disconnect, address 2
More information about the linux
mailing list